Today I awoke feeling really horny, but wifey has to go to work today, so that leaves me at home all alone.
We all know what happens when wifey leaves me at home alone, don’t we?Yes, I just can’t resist the temptation to masturbate, and my temptation always wins out.
Today was no different, and as wifey prepared to herself for work, I was patiently waiting for her to leave so that I could pull my cock out and masturbate.
Once wifey had left, and driven away, it was a quick trip for the KY and off to the computer room.
But today I thought I should try a different masturbation technique.
Remembering that I had made a home made version of a “flesh light”, it was off to the basement where I rummaged through some old boxes and found my masturbation tube.
Taking the device back upstairs to the computer room, it was a matter of seconds, and my pants were off and my cock at full attention in anticipation of the activities that lay ahead.
Applying a generous amount of KY onto my cock and around the opening and throat of my device, I slowly inserted my throbbing cock into the canal.
As I slowly slid the device down the full length of my cock, it felt just like a nice tight pussy, but not as warm.
Once the tube had been slid up and down my cock a few times, it felt so good that I started to increase my cadence, and before long, my cock started to pulse and within moments I was at the point of no return and about to cum.
My cock started to ejaculate, and as my orgasm started, I kept sliding that device up and down the length of my cock and enjoying every moment of pleasure this device could give.
Of course, there were the naked ladies posted above to heighten my orgasm, some of which are posted above for your viewing and masturbation pleasure.
To make your own “Flesh-Light” like the one pictured above, it is a simple and easy thing to do with minimum materials required and about 20 minutes of your time to make.
Cut a piece of 2” PVC plastic pipe (white or black, it does not matter) 6” long and round off the saw marks and sharp edges with sandpaper or emery cloth.
The rounding of the edges is most important to achieve maximum life out of your inner tube.
Next, take an old bicycle inner tube and cut a piece 8”long and drill 3 or 4 - 1/4” holes around the middle of the pipe to allow air to escape when you insert your cock.
If you do not drill the holes, it will be very difficult to insert you cock because there will be no place for the air to go once you start inserting your cock.
Take the inner tube and slip it through the middle of your PVC pipe, and fold the end of the inner tube over the end of the PVC pipe.
Ensure that your inner tube has the molded seams on the outside, and the smooth inside now becomes the outside or canal once inserted through the PVC pipe.
Failing to ensure that the smooth surface is not in the “canal” will cause much discomfort and possible lacerations to your cock from the sharp molded edges.
We sure don’t want to harm ourselves so this is a most important step.
It does not matter of you have exactly 1” folded over the end of the pipe or not, as long as the canal inside the PVC pipe is fairly straight and wrinkle or fold free.
Then, fold the other end of the inner tube over the end of the PVC pipe.
Because there is a bit of tension on the inner tube as it is stretched over the end of the PVC pipe, this is why you need to ensure there are no sharp edges, as your inner tube will tear at the sharp edge after a short period of time, rendering your new toy useless.
Be careful not to twist the inner tube inside the pipe, as it will be difficult to slip your cock into when it is time to try out your new toy.
To use your new toy, just lube up your cock with KY or some other favorite lubricant and insert your cock.
Slide the tube up and down the length of your cock, and it will feel nice and snug, just like a nice tight pussy.
You can slide the device as fast or slow as you want to give the maximum pleasure.
When the time is right for you to ejaculate, most of your mess will be inside the tube, and is easy to wash up after.
To wash, rinse with warm soapy water, dry and hide the device in a safe place so that wifey does not see it and ask questions.
Feel free to contact me for more information about making or using the device, and I will be more than happy to reply with as much detail as I can.
Happy masturbating!
Then, fold the other end of the inner tube over the end of the PVC pipe.
Because there is a bit of tension on the inner tube as it is stretched over the end of the PVC pipe, this is why you need to ensure there are no sharp edges, as your inner tube will tear at the sharp edge after a short period of time, rendering your new toy useless.
Be careful not to twist the inner tube inside the pipe, as it will be difficult to slip your cock into when it is time to try out your new toy.
To use your new toy, just lube up your cock with KY or some other favorite lubricant and insert your cock.
Slide the tube up and down the length of your cock, and it will feel nice and snug, just like a nice tight pussy.
You can slide the device as fast or slow as you want to give the maximum pleasure.
When the time is right for you to ejaculate, most of your mess will be inside the tube, and is easy to wash up after.
To wash, rinse with warm soapy water, dry and hide the device in a safe place so that wifey does not see it and ask questions.
Feel free to contact me for more information about making or using the device, and I will be more than happy to reply with as much detail as I can.
Happy masturbating!
Posting Komentar